II. Speaking Exercises

Exercise 1. Describe deformation;   deflection;    bending;   torsion; helix; suspension,  using the suggested words and expressionsas in example:

deformation alteration of shape; stresses; thermal expansion; transformations; shrinkage; expansions. example:Deformation is any alteration of shape or dimensions of a body caused by stresses, thermal expansion or contraction, chemical or metallurgical transformations, or shrinkage and expansions due to moisture change.

deflection shape change; reduction in diameter; without fracturing the material.

bending a metal part; pressure; a curved shape; angular shape; the stretching; flanging; a curved path.

torsion a twisting deformation; a solid body; an axis; lines parallel to; helices.

suspension wire; coil; spring; support; the moving element;

helix    a curve; a cylindrical or conical surface; points of the surface; at the same angle

 

Exercise 2. Ask questions to the given answers:

1) Question: ___________________________________________?

Answer: This type of spring is the most common

2) Question: ___________________________________________?

Answer: A tension spring can be wound with initial pre-load so that it deforms only after the load reaches a certain minimum value.

3) Question: ___________________________________________?

Answer: Rotary springs involve torque and angular deflection.

4) Question: ___________________________________________?

Answer: The helical torsion spring is similar to the helical tension spring in requiring specially formed ends to transmit the load.

 

 

III. Writing exercises:

Exercise 1. Complete the sentences with the suggested words: used; exists; find; is; are;

The constant force spring ___ not unlike a self- retracting tape measure and is ____ where large relative displacements ____ required - the spring motors used in sliding door closers is one application. There _____ also a large variety of non-metallic springs often applied to shock absorption and based on rubber blocks loaded in shear. Springs utilising gas compressibility also ______ some use.

 

Exercise 2. Fill in the table with words and expressions from the text:

	parts	place	processes
Example: Rotary springs involve			torque and angular deflection
Torsion bars are stiff compared to
Springs are common also in
The (ex)tension spring is similar to

Exercise 3. Compose a story on one of the topics (up to 100 words):

“Recoverable mechanical energy”

“The simplest spring”

“The leaf spring”

“The shortcoming of most metal springs”

 

 

Lesson 4

 

Read the text: BATTERIES

The battery is the primary "source" of electrical energy on vehicles. It stores chemicals, not electricity. Two different types of lead in an acid mixture react to produce an electrical pressure. This electrochemical reaction changes chemical energy to electrical energy.

Battery Functions:

1. ENGINE OFF: Battery energy is used to operate the lighting and accessory systems.

2. ENGINE STARTING: Battery energy is used to operate the starter motor and to provide current for the ignition system during cranking.

3. ENGINE RUNNING: Battery energy may be needed when the vehicle's electrical load requirements exceed the supply from the charging system. In addition, the battery also serves as a voltage stabilizer, or large filter, by absorbing abnormal, transient voltages in the vehicle's electrical system. Without this protection, certain electrical or electronic components could be damaged by these high voltages.

Battery Types

1. PRIMARY CELL: The chemical reaction totally destroys one of the metals after a period of time. Small batteries for flashlights and radios are primary cells.

2.  SECONDARY CELLS: The metals and acid mixture change as the battery supplies voltage. The metals become similar, the acid strength weakens. This is called discharging. By applying current to the battery in the opposite direction, the battery materials can be restored. This is called charging. Automotive lead-acid batteries are secondary cells.

3. WET-CHARGED: The lead-acid battery is filled with electrolyte and charged when it is built. During storage, a slow chemical reaction will cause self-discharge. Periodic charging is required.

4. DRY-CHARGED: The battery is built, charged, washed and dried, sealed, and shipped without electrolyte. It can be stored for 12 to.18 months. When put into use, it requires adding electrolyte and charging.

5. LOW-MAINTENANCE: Such batteries are built to reduce internal heat and water loss. The addition of water should only be required every 15,000 miles or so.

The battery is one of the most important components on a vehicle today. It provides the amps needed to crank and start the engine, and it stores the voltage that runs everything from the ignition system and fuel injectors to the vehicle’s lights and all of its electrical accessories. Lead-acid batteries have been around since the earliest days of the automobile and have steadily improved over the years. Today’s batteries are more durable, have high power-to-weight ratios and lighter cases. But the basic chemistry is unchanged. A chemical reaction between two dissimilar metals in an acid solution creates voltage. The two dissimilar metals are lead and lead peroxide. The active material on the positive plates are lead peroxide (a soft, dark brown material), while that on the negative plates is finely ground “sponge” lead (which is gray in color). The positive and negative plates are sandwiched together and separated by a nonconductive insulating layer of paper, plastic or mirco-woven glass.

The acid is a mixture of 25 percent water and 75 percent sulfuric acid (H2SO4). Battery acid is called the “electrolyte” because it allows charged particles (called “ions”) to move between the plates when current is drawn from the battery. A 12-volt battery has six “cells,” each of which contains 9 to 20 positive and negative plates. The greater the number of plates, the higher the power output (measured in amps) of the battery. Each cell produces 2.11 volts, so when all six cells are connected together in series, the battery’s total output is actually 12.66 volts. As a battery discharges, sulfate combines chemically with the positive and negative plates. This lowers the concentration of acid in the solution, which can be measured by checking the “specific gravity” (density) of the liquid with a hydrometer or built-in charge indicator. As more and more current is pulled out of the battery, sulfate continues to build up on the plates, and the concentration of the acid drops until the battery becomes discharged and no longer produces enough voltage to crank the engine or power the lights or other accessories.

To reverse the chemical reaction and recharge the battery, the charging system senses any drop in voltage and increases its voltage output to push amps back into the battery. This forces the sulfate away from the plates and puts it back into the solution. The concentration of acid goes back up, and the battery returns to full charge.

To produce maximum cranking power and remain healthy, an automotive lead-acid battery must be kept at or near full charge. If the battery is allowed to run down (leaving the lights on, low charging output, slipping drive belt, frequent short-trip driving, long periods of inactivity, etc.), sulfate can form a barrier on the surface of the plates that makes it difficult for the battery to accept a charge. Over time, this can ruin the plates and cause the battery to fail.